FLOPAM FO 4700 Family Equivalent: High-Charge Cationic PAM Supply Route
ChinaPAM supplies cationic PAM powder for FLOPAM FO 4700 family purchasing inquiries. Start with C8005 for bare FO 4700 or FO 4700 SH duty. If the bag says FO 4700 SSH, we route the inquiry to C8055 because that suffix moves to the Very High charge and Very High molecular-weight bands in the historical SNF catalogue. Send the exact suffix or a bag-label photo to receive current pricing and sample options; process details can follow.
Supply Route Comparison
Published reference data and the ChinaPAM route for SNF FLOPAM FO 4700 / FO 4700 SH / FO 4700 SSH
Competitor reference: SNF SAS Catalogue 2007 Poudres, pages 6, 8 and 12. The cited values are historical, indicative figures measured under SNF's stated conditions, not current contractual specifications; manufacturer descriptor scales are not calibrated to one another.
| Parameter | ChinaPAM Supply Route | SNF FLOPAM FO 4700 / FO 4700 SH / FO 4700 SSH |
|---|---|---|
| Bare FO 4700 profile | C8005 starting route: High charge / High molecular weight on the ChinaPAM scale | High charge / Standard molecular weight; approximately 600 / 270 / 130 cps at 5 / 2.5 / 1 g/L (SNF 2007 p12) |
| FO 4700 SH profile | C8005 starting route: High charge / High molecular weight on the ChinaPAM scale | High charge / High molecular weight; approximately 550 / 230 / 100 cps at 5 / 2.5 / 1 g/L (SNF 2007 p8) |
| FO 4700 SSH profile | C8055 conditional route: Very High charge / Very High molecular weight on the ChinaPAM scale | Very High charge / Very High molecular weight; approximately 620 / 300 / 140 cps at 5 / 2.5 / 1 g/L (SNF 2007 p6) |
| Historical SNF make-up | Use ChinaPAM instructions below for the selected grade | Bare and SH: 4 g/L recommended, 10 g/L maximum, 60 min; SSH: 3 g/L recommended, 5 g/L maximum, 90 min in DI water at 5 g/L and 25°C (SNF 2007 pp6, 8, 12) |
| ChinaPAM make-up | 1–3 g/L recommended, 5 g/L maximum, dissolution within 60 min at working concentration | Historical SNF conditions are shown for identification and equipment review, not as ChinaPAM instructions |
Specifications
| Primary supply grade | C8005 for bare FO 4700 and FO 4700 SH screening |
| Primary grade position | High charge / High molecular weight (ChinaPAM scale) |
| Conditional alternate | C8055 for FO 4700 SSH screening only |
| Conditional grade position | Very High charge / Very High molecular weight (ChinaPAM scale) |
| Our polymer | Cationic PAM powder |
| Our recommended make-up | 1–3 g/L |
| Our maximum make-up | 5 g/L |
| Our dissolution | ≤60 min at working concentration |
Key Features
- C8005 primary route for bare and SH inquiries
- C8055 conditional SSH route triggered by the complete bag label
- Three FO 4700 suffix profiles kept separate during quotation and trial planning
Applications
- Alternative supply screening for buyer-specified FLOPAM FO 4700, FO 4700 SH or FO 4700 SSH duty
- Make-up and dosing-system checks during an incumbent cationic polymer changeover
- Feed-specific clarification and dewatering trials with the exact incumbent suffix recorded
Get a Quote for SNF FLOPAM FO 4700 / FO 4700 SH / FO 4700 SSH Alternative Supply
Start with the grade name, a bag-label photo or your purchasing requirement. We can discuss current pricing and sample options now; process details can follow.
Related Articles
The FO 4700 suffix changes the selection route
The 2007 SNF powder catalogue lists bare FO 4700 on page 12 at High charge and Standard molecular weight, with indicative Brookfield readings of 600 / 270 / 130 cps at 5 / 2.5 / 1 g/L. Its historical make-up entry is 4 g/L recommended, 10 g/L maximum and 60 minutes in deionized water at 5 g/L and 25 degrees C.
FO 4700 SH is a separate page 8 entry at High charge and High molecular weight. Its indicative Brookfield profile is 550 / 230 / 100 cps, with 4 g/L recommended, 10 g/L maximum and 60-minute dissolution under the same stated SNF test conditions.
FO 4700 SSH moves both descriptors: page 6 lists Very High charge and Very High molecular weight, 620 / 300 / 140 cps, 3 g/L recommended, 5 g/L maximum and 90-minute dissolution under the stated SNF conditions. These three historical rows are why the complete suffix is required before the sample route is finalized.
One primary route and one suffix-controlled alternate
C8005 is our primary starting grade for bare FO 4700 and FO 4700 SH inquiries. It is cationic PAM powder at High charge and High molecular weight on the ChinaPAM scale. The SH descriptors line up at the broad-band level; the bare incumbent's Standard molecular-weight label does not establish numerical equality to our High band, so the actual feed trial remains the decision point.
C8055 is reserved as the conditional route when the exact incumbent is FO 4700 SSH. It is cationic PAM powder at Very High charge and Very High molecular weight on our scale. We do not switch an un-suffixed or SH inquiry to C8055 merely to chase a higher molecular-weight label. Prepare either ChinaPAM candidate at 1–3 g/L, never above 5 g/L, and allow up to 60 minutes for dissolution at working concentration.
Failure modes the suffix check prevents
Under-routing an SSH inquiry: supplying the High-charge C8005 route without confirming an SSH bag label may miss the incumbent's Very High charge and Very High molecular-weight position. Weak floc after shear, lower cake solids or rising filtrate or centrate turbidity are the practical warning signs. Compare C8055 at matched delivered polymer mass before increasing dose.
Over-routing a bare or SH inquiry: moving directly to the Very High-charge C8055 route can overshoot the feed's charge demand. A narrow optimum, worse clarity after a small dose increase or floc restabilization indicates that the charge route may be too high; return to C8005 rather than continuing to add polymer.
Preparation mismatch: using the bare or SH 60-minute historical release schedule for an SSH incumbent ignores the SSH catalogue's 90-minute reference. Check residual particles, solution uniformity and measured pump delivery before blaming the chemistry. Use ChinaPAM's own 1–3 g/L, maximum 5 g/L and ≤60-minute instructions for our product instead of copying either incumbent recipe.
Get the FO 4700 route quoted
Send FO 4700, FO 4700 SH or FO 4700 SSH exactly as printed on the bag, or send a bag-label photo and purchasing quantity. We can discuss the applicable C8005 or C8055 route, current pricing, sample options and available order documents first; feed, equipment and performance details can follow for the trial plan.
Dosage Guide
Prepare the selected ChinaPAM powder at 1–3 g/L, maximum 5 g/L, and allow up to 60 minutes for dissolution at working concentration. Make-up concentration is separate from treatment dose. Start the comparison at matched delivered polymer mass and evaluate clarity, floc response to shear and the relevant dewatering endpoint on the actual feed.
Frequently Asked Questions — FLOPAM FO 4700 Family Equivalent: High-Charge Cationic PAM Supply Route
Which ChinaPAM grade should I request for FLOPAM FO 4700 duty?
Request C8005 as the starting route for bare FO 4700 or FO 4700 SH duty. If your label says FO 4700 SSH, tell us before sampling; that suffix moves to Very High charge and Very High molecular weight in the historical SNF range, so we route the inquiry to C8055.
Can I use one route for every FO 4700 suffix?
The suffix must be kept. The 2007 SNF catalogue separates bare FO 4700 at High charge / Standard molecular weight, SH at High / High and SSH at Very High / Very High. C8005 is the primary bare and SH route, while C8055 is the conditional SSH route; the actual feed trial decides the result.
How should I prepare the ChinaPAM trial solution?
Prepare our powder at 1–3 g/L, never above 5 g/L, and allow up to 60 minutes for dissolution at working concentration. Do not copy the historical SNF recipe onto our grade. Compare at matched delivered polymer mass and record clarity, shear response and the relevant dewatering endpoint.
What should I send for pricing and a sample?
Send the exact grade string or a bag-label photo plus the purchasing quantity. We can discuss the correct C8005 or C8055 route, current pricing and sample options immediately; process details can follow for trial design.
Related Products
Trademark notice. SNF FLOPAM FO 4700 / FO 4700 SH / FO 4700 SSH and all other third-party product and brand names on this page are trademarks or registered trademarks of their respective owners. Henan Jinghua New Material Technology Co., Ltd. is not affiliated with, endorsed by, sponsored by or authorised by those owners, and no such relationship is implied. Those names are used here for the sole purpose of identifying the products our grades are compared against, which is necessary to describe what we supply. Our products are independently manufactured and are not licensed copies. Grade descriptors quoted for third-party products are taken from each manufacturer’s own published literature and follow that manufacturer’s own scale; we do not publish figures those manufacturers do not publish. Performance on your process should be confirmed by jar test or CST test before any change of supply.