Magnafloc 504 Alternative Supply — Cationic Route Screening
ChinaPAM accepts a Magnafloc 504 alternative-supply enquiry and can quote a cationic selection programme once the material, duty and preparation system are confirmed. A current Solenis UK Industries Limited SDS identifies the product as a granular flocculant. A current Quadra product page — Quadra is a distributor that names Solenis as supplier on that page — describes Magnafloc 504 as a low-MW, high-charge cationic PAM in free-flowing micro-bead form; the Quadra page is a Canada-based distributor context and is not a Solenis-issued PDS. ChinaPAM has no Low-MW cationic row and no micro-bead row in the published product range. C8002 and C8025 are charge-side trial anchors; MW and form require a test. Send the Magnafloc 504 label and your process details and ChinaPAM will open the programme.
Supply Route Comparison
Published reference data and the ChinaPAM route for Magnafloc 504
Magnafloc is a trademark of Solenis and/or its affiliates. ChinaPAM is an independent manufacturer and is not affiliated with, endorsed by, licensed by or a distributor for Solenis or Quadra. Sources cited: current Solenis UK SDS R1201884 (2024-11-19) and Quadra distributor page (captured 2026-10-07, naming Solenis as supplier) — they are not ChinaPAM documents. Our products are separately branded ChinaPAM grades and are not licensed copies.
| Parameter | ChinaPAM Supply Route | Magnafloc 504 |
|---|---|---|
| Product form | Cationic PAM powder; form differs from micro-bead/granule; check make-down equipment compatibility | Off-white odourless granular flocculant — current Solenis SDS R1201884 (2024-11-19) |
| Distributor-described profile | No Low-MW cationic or micro-bead grade in the current ChinaPAM product range; C8002/C8025 are charge-side anchors only | Low MW, high charge, free-flowing micro-bead — Quadra distributor page (names Solenis as supplier); not an issuer-hosted PDS |
| Charge position | C8002/C8025 medium-MW high-charge powder anchors; charge-side alignment only | High charge — Quadra distributor page (bounded secondary context) |
| Molecular weight | No Low-MW ChinaPAM cationic grade; MW gap requires trial and process testing | Low MW — Quadra distributor page (bounded secondary context; not issuer-verified) |
| Solution pH | Confirmed against quoted ChinaPAM grade at quotation | 3.5–4.5 at 10 g/L — current Solenis SDS R1201884, Section 9 |
| Make-down | ChinaPAM powder preparation runs at a 1–3 g/L recommended window, 5 g/L maximum, and no longer than 60 minutes at working concentration. Preparation concentration is not process dosage. Verify that existing wetting equipment handles powder rather than micro-bead. | Quadra page describes bounded stock and feed-solution concentration ranges as competitor preparation context; do not copy into ChinaPAM instructions |
Specifications
| Incumbent Model | Solenis Magnafloc 504 (material 933408; keep separate from 380, 455 and other Magnafloc pages) |
| Current SDS Identity | Solenis UK Industries Limited SDS R1201884, version 1.0, revision 2024-11-19: off-white odourless granular flocculant, pH 3.5–4.5 at 10 g/L, viscous solution in water |
| Ionic Type | Cationic PAM — Quadra current product page (distributor, names Solenis as supplier, captured 2026-10-07); not confirmed by the current Solenis SDS alone |
| Current Profile (Distributor) | Low MW, high charge, free-flowing micro-bead — Quadra current product page (distributor, names Solenis as supplier; captured 2026-10-07; Canada; not an issuer-hosted PDS) |
| ChinaPAM Charge-Side Anchors | C8002, C8025 — medium-MW, high-charge powder; charge direction only; neither is Low-MW or micro-bead |
| Route Boundary | Grade-selection screening — no public primary/backup named; form, MW and make-down require a same-material test |
Key Features
- Current Solenis UK Industries Limited SDS (R1201884, 2024-11-19) confirms exact product identity and granular form
- Quadra distributor page (current, names Solenis as supplier, captured 2026-10-07) provides the bounded cationic / low-MW / high-charge / micro-bead profile context
- The Quadra page is a Canada-based distributor page — it cannot be read as evidence of worldwide Solenis supply availability
- Conflicting competitor pages (cationic on one, anionic on another) are rejected; the current Solenis SDS establishes identity and granular form only — it does not establish ionic type, MW or charge; Quadra, acting as a distributor naming Solenis as supplier, separately provides the cationic / low-MW / high-charge / micro-bead profile context; the conflicting ionic classifications are NOT resolved by the Solenis SDS
- ChinaPAM has no Low-MW cationic row and no micro-bead row; C8002/C8025 are charge-side trial anchors only
- Make-down differences between powder and micro-bead / granule forms require checking before trial design
- Same-material trial required; current incumbent label, SDS or datasheet requested from the buyer
Applications
- Buyer-confirmed solid-liquid separation duty where the incumbent is Magnafloc 504; the Quadra page describes this application context (naming Solenis as supplier), but the buyer's confirmed real duty determines the trial design
- Buyer-confirmed or Quadra-described mineral gravity clarification where cationic charge coagulation is the selection criterion, with optional anionic co-flocculant combination considered — the actual duty must be confirmed by the buyer before trial design
- Procurement comparing a confirmed Magnafloc 504 requirement with a cationic PAM selection programme
- Buyer-confirmed processes where existing wetting and aging equipment can be verified to accommodate a powder preparation approach rather than micro-bead or granule input
Get a Quote for Magnafloc 504 Alternative Supply
Send the Magnafloc 504 label or bag photo. Attach the current SDS or product datasheet if available. State your duty — the separation target, slurry or feed concentration, preparation system and equipment. That is enough to open the enquiry.
Related Articles
Supply answer: cationic selection programme; form and MW gap acknowledged
ChinaPAM accepts a Magnafloc 504 alternative-supply enquiry and can open a cationic-powder selection programme. No public primary or backup is named in advance because the current ChinaPAM product range has no Low-MW cationic row and no micro-bead row. The closest charge-direction anchors are C8002 and C8025 (medium-MW, high-charge, powder); they align on charge but differ on MW and physical form from the distributor-described micro-bead profile.
The programme design requires: confirming the current incumbent exact documents; checking whether existing wetting and aging equipment can accommodate a powder instead of a micro-bead or granule preparation; running the charge-direction anchors on the same representative material at the same active dose and documented make-down conditions; and comparing separation performance before naming a commercial route.
Price, stock and lead time belong to the quotation.
Two source chains: current Solenis SDS and Quadra distributor page
The current Solenis UK Industries Limited SDS R1201884 (version 1.0, revision 2024-11-19, material 933408) is the authoritative document for exact product identity: Magnafloc 504 FLOCCULANT, off-white odourless granular form, flocculating agent use, pH 3.5–4.5 at 10 g/L. The SDS does not state ionic type, MW or charge.
Quadra's current public product page (captured 2026-10-07) names Solenis as supplier and, as a distributor, separately provides bounded cationic / low-MW / high-charge / micro-bead product-profile context. Quadra is a distributor — this is a current distributor page, not an issuer-hosted byte archive of a Solenis PDS. The Solenis SDS establishes identity and granular form only. The SDS and the Quadra page are separate and non-overlapping source chains: the SDS for identity and granules; the Quadra distributor page for the cationic / low-MW / high-charge / micro-bead profile. The page is Canadian; it does not establish that Magnafloc 504 is available worldwide from Solenis at any given time.
Two competing supplier pages — one calling 504 cationic and one calling it anionic — are contradictory. Both are rejected as product-fact sources. The Solenis SDS establishes identity and granular form only — it does not publish any ionic classification and therefore does not resolve the conflicting ionic classifications. The Quadra distributor page, naming Solenis as supplier, is the accepted secondary source for the cationic / low-MW / high-charge / micro-bead profile.
Three facts the sources actually establish
| Fact | Source and locator | What it does not establish |
|---|---|---|
| Magnafloc 504 FLOCCULANT, material 933408, is identified for use as a flocculating agent. | Current Solenis UK Industries Limited SDS R1201884, version 1.0, revision 2024-11-19; PDF page 1, identification and recommended use. | Does not state ionic type, MW or charge. |
| The product is described as off-white, odourless granules; pH 3.5–4.5 at 10 g/L; forms a viscous solution in water. | Current Solenis SDS R1201884; PDF pages 6–7, Section 9. | pH at 10 g/L only. The SDS does not state ionic type, MW or charge. |
| Quadra's current product page names Solenis as supplier and describes Magnafloc 504 as a low-MW, high-charge cationic PAM in free-flowing micro-bead form; it notes solid-liquid separation, optional anionic co-flocculant combination, mineral gravity clarification, and bounded preparation ranges. | Quadra current product page; captured 2026-10-07; locator: page lines 1636–1668 (identity/profile) and 1682–1696 (applications/preparation). Condition: current distributor context; not issuer-hosted PDS. | Quadra is a distributor and the page is Canadian. Does not prove global Solenis availability, ChinaPAM equivalence or performance guarantee. |
Two failure modes and the check that catches each one
| Trigger | Consequence | Verification step |
|---|---|---|
| A conflicting anionic product page from an unrelated third party is treated as product truth, or the unrelated third-party anionic classification of related grade numbers is accepted without checking the current Solenis source chain. | The wrong ionic family can be quoted or tested, wasting the sample trial and potentially producing a result that fails not for chemistry reasons but because the ionic classification was wrong from the start. | Use the current Solenis SDS as the authoritative source for identity and granular form only — it does not state ionic type and does not resolve ionic classification questions. Use the Quadra distributor page (naming Solenis as supplier) as the bounded secondary source for the cationic / low-MW / high-charge / micro-bead profile. To confirm ionic identity, require the exact incumbent label, bag or a current issuer product document — do not rely solely on competitor-copy pages for ionic classification. |
| A medium-MW ChinaPAM powder is presented as an exact low-MW micro-bead match because its charge band is high. | The current ChinaPAM product range has no Low-MW cationic or micro-bead row; C8002/C8025 are charge-side anchors only. MW difference and form difference affect dissolution speed, shear response and settling or clarification performance. Reporting a charge match without disclosing the MW and form gap overstates the trial probability of success. | Confirm make-down compatibility between the buyer's existing preparation equipment and a powder format before trial. Compare separation performance and solution quality on the same material at the same active dose before naming a route. |
Intake, trial design and acceptance metrics
Useful intake: full Magnafloc 504 label and current incumbent SDS or product datasheet; current stock or feed concentration; active dose; mineral or solids profile; pH; ionic strength; water hardness; current throughput; clarification or dewatering equipment; settling or filtration rate target; make-down preparation system; and whether an anionic co-flocculant is in current use and which one.
ChinaPAM powder preparation runs at a 1–3 g/L recommended window, 5 g/L maximum, and no longer than 60 minutes at working concentration. Preparation concentration is not process dosage. Check whether existing wetting and aging equipment can handle powder rather than free-flowing micro-bead or granule input.
Trial design: run a documented dose ladder on the same representative material using identical make-down concentration, mixing and agitation conditions for every candidate run. If a co-flocculant sequence is to be compared, it may be included only when that sequence already exists in the buyer's real operating condition; do not introduce a co-flocculant programme that the buyer does not currently run. After selecting a leading route from the dose ladder, repeat it on an adverse but real feed or water condition supplied by the buyer before committing to scale-up. Do not copy Quadra preparation concentration ranges into ChinaPAM instructions; apply ChinaPAM TDS make-down guidance for the selected grade.
Agree acceptance metrics before the first run: clarity or turbidity; settling rate; underflow concentration or cake solids; active dose; throughput; solution quality; make-down time; handling reliability. Buyer-defined targets take precedence.
Current price, stock status, lead time, applicable TDS and sample arrangements are confirmed in the quotation. Batch-specific COA terms are confirmed with the shipment.
Brand Equivalents & Replacements
ChinaPAM accepts a Magnafloc 504 alternative-supply enquiry and can open a cationic selection programme. No public primary or backup is named because the current ChinaPAM product range has no Low-MW cationic or micro-bead row. C8002 and C8025 are charge-side anchors only. Neither is a drop-in or performance-guaranteed replacement.
| Brand | Grade | Notes |
|---|---|---|
| Solenis Magnafloc | 504 | Current Solenis UK SDS R1201884 (2024-11-19): material 933408; off-white odourless granular flocculant; pH 3.5–4.5 at 10 g/L; viscous solution in water. Quadra current distributor page (captured 2026-10-07, names Solenis as supplier, Canada page): low-MW, high-charge cationic PAM, free-flowing micro-bead form; solid-liquid separation; optional co-flocculant. Distributor context only; not issuer-hosted PDS. ChinaPAM: no Low-MW cationic or micro-bead row in the published product range; C8002/C8025 are charge-side anchors only. Grade-selection screening; trial determines route. |
Need a replacement for a different grade? Contact us with your current product specs.
Frequently Asked Questions — Magnafloc 504 Alternative Supply — Cationic Route Screening
Can ChinaPAM supply for a Magnafloc 504 requirement?
Yes — ChinaPAM accepts the enquiry and can open a cationic-powder selection programme. No specific grade is pre-named in advance because the current ChinaPAM product range has no Low-MW cationic or micro-bead row. C8002 and C8025 are charge-side trial anchors only. The programme confirms the route after testing on the same material at matched dose and make-down conditions.
The Quadra distributor page describes Magnafloc 504 as low-MW high-charge micro-bead. Is that the same as a Solenis-issued PDS?
No. The Quadra page is a current distributor product page that names Solenis as supplier; it is not a byte archive of a Solenis-hosted PDS. The Solenis SDS establishes identity and granules only; Quadra, acting as a distributor, separately provides the cationic / low-MW / high-charge / micro-bead description. The Quadra page is also Canadian — it does not establish that Magnafloc 504 is available worldwide from Solenis.
One supplier lists 504 as cationic and another lists it as anionic. Which is correct?
The current Solenis UK SDS R1201884 establishes identity and form only — it does not state ionic type. The Quadra distributor page (naming Solenis as supplier) separately describes Magnafloc 504 as cationic. Both competing supplier pages are contradictory and neither is an issuer-backed document. This page uses the Solenis SDS as the authoritative source for identity and form, and the Quadra distributor page as bounded secondary context for the cationic / low-MW / high-charge / micro-bead profile.
When should a Magnafloc 504 alternative-supply programme proceed, and when should it stop?
Proceed when a tested ChinaPAM route meets the separation and preparation-system targets on the same representative material at matched dose and make-down conditions. Stop or reformulate when low-MW behaviour or micro-bead form is essential to the buyer's process and the powder route cannot meet that requirement — charge alignment alone is not sufficient if MW and form are critical to the separation duty.
How do the documented profiles of Magnafloc 455 and 504 compare?
Magnafloc 455 has a historical very-low-charge profile recorded in EP 3019271 B1. Magnafloc 504 has a current distributor-described high-charge profile from Quadra (which names Solenis as supplier). Those are opposite ends of the cationic charge range. Each grade belongs in its own enquiry — the charge requirement and the trial design differ substantially between them.
What is confirmed in the quotation, and what is not stated here?
Current price, stock status, lead time, applicable TDS and sample arrangements are confirmed in the quotation. Batch-specific COA terms are confirmed with the shipment.
Trademark notice. Magnafloc 504 and all other third-party product and brand names on this page are trademarks or registered trademarks of their respective owners. Henan Jinghua New Material Technology Co., Ltd. is not affiliated with, endorsed by, sponsored by or authorised by those owners, and no such relationship is implied. Those names are used here for the sole purpose of identifying the products our grades are compared against, which is necessary to describe what we supply. Our products are separately branded ChinaPAM grades and are not licensed copies. Third-party facts on this page are attributed separately to the current Solenis UK SDS and the Quadra Canada distributor page, preserving Solenis as supplier and Quadra as distributor; the distributor page is not presented as an issuer-hosted product data sheet. Performance on your process should be confirmed by jar test or CST test before any change of supply.