FLOPAM EM 532 Alternative — Anionic Emulsion Selection for PHPA Duty
ChinaPAM can respond to an exact FLOPAM EM 532 requirement with an anionic emulsion selection service and a current quotation. Send the EM 532 label, the available datasheet, the treated fluid, salinity, temperature, present dose and equipment. We screen ZJ033 first only where the documented oilfield-PHPA duty fits, and keep ZJ050 as the sole conditional backup for salt-resistant or high-salinity duty. This is a test-order route, not a claim that either ChinaPAM grade is identical to FLOPAM EM 532.
Supply Route Comparison
Published reference data and the ChinaPAM route for FLOPAM EM 532
FLOPAM is a trademark of SNF Group and/or its affiliates. ChinaPAM is an independent supplier and is not affiliated with, endorsed by, licensed by or a distributor for SNF. The exact FLOPAM EM 532 name is used only to identify the incumbent a buyer is comparing. Incumbent values are attributed to SNF sas's historical 2007 emulsions catalogue, physical page 6, and are indicative historical values rather than current specifications. The ZJ033 and ZJ050 statements apply only to those ChinaPAM document subjects and do not establish one-to-one equivalence. Our products are separately branded ChinaPAM grades and are not licensed copies.
| Parameter | ChinaPAM Supply Route | FLOPAM EM 532 |
|---|---|---|
| Product identity and form | ZJ033 or conditional ZJ050 anionic PHPA emulsion, each under its own ChinaPAM document and duty boundary | FLOPAM EM 532 anionic emulsion — historical SNF 2007 catalogue, physical page 6 |
| Charge basis | ZJ033 hydrolysis 35–38%; ZJ050 hydrolysis 50–55%. These are grade-document values, not an SNF-charge conversion. | Medium charge — SNF supplier-relative historical label; no numeric cross-vendor calibration is published |
| Molecular-weight basis | ZJ033 17–19 million Da; ZJ050 19–21 million Da, each within its documented PHPA scope | High molecular weight — qualitative historical catalogue label |
| Solids / non-volatile solids | ZJ033 solids 32–35% w/w; ZJ050 solids 36–40% w/w under their own grade documents | Average non-volatile solids 36.0% — historical indicative value; not automatically the same analytical basis |
| Viscosity basis | Candidate values remain tied to their own 0.1%, 25°C method and are not compared numerically to the incumbent value | Approx. 1,800 cps at 5 g/L active — historical SNF catalogue condition |
| Route ranking | ZJ033 first only after compatible duty confirmation; ZJ050 only when salt resistance or high salinity requires it | No current route or availability conclusion can be drawn from the historical catalogue |
| Commercial confirmation | Current ChinaPAM grade documents, availability, price, lead time and sample arrangements are confirmed for the selected route in the quotation. The historical FLOPAM catalogue does not establish current commercial terms for either side. | Current FLOPAM EM 532 specification, stock and commercial terms are not established by the historical 2007 SNF catalogue |
Specifications
| Incumbent Model | FLOPAM EM 532 — bare model identity; do not import EM 533 or EM 630 facts |
| Historical Identity | Anionic polyacrylamide emulsion — SNF emulsions catalogue 2007, physical page 6 |
| Historical Charge / MW | Medium charge / High molecular weight — supplier-relative labels; no cross-vendor numeric conversion |
| Historical Bulk Values | Approx. 1,200 cps bulk viscosity; bulk density 1.04; average non-volatile solids 36.0% — indicative catalogue values |
| Historical Working-Solution Values | Dilution 58 to 5 g/L active; approx. 1,800 cps at 5 g/L; maximum operating concentration 5 g/L; DI-water solution stability 8 days |
| Historical Storage / Packing | Six-month shelf life; 0–35°C storage; 25 kg pail, 1,050 kg IBC or 22–24 t bulk — historical and indicative only |
| ChinaPAM First Screen | ZJ033 anionic PHPA emulsion only after compatible oilfield-PHPA duty is confirmed; documented hydrolysis 35–38%, molecular weight 17–19 million Da and solids 32–35% w/w |
| Conditional Backup | ZJ050 salt-resistant anionic PHPA emulsion only for high-salinity duty or the relevant higher documented hydrolysis range; documented hydrolysis 50–55%, molecular weight 19–21 million Da and solids 36–40% w/w |
| Selection Boundary | Same form and ionic family do not establish equal chemistry, charge scale or performance; same-duty testing decides |
| Current Commercial Terms | Current ChinaPAM grade documents, availability, price, lead time and sample arrangements are confirmed for the selected route in the quotation. The historical FLOPAM catalogue does not establish current commercial terms for either side. |
Key Features
- Exact EM 532 identity is kept separate from EM 533 and EM 630 throughout the page
- Historical Medium-charge and High-molecular-weight labels remain attributed to the SNF 2007 catalogue
- ZJ033 is named only as a duty-conditioned first screen for compatible oilfield-PHPA service
- ZJ050 is restricted to salt-resistant or high-salinity conditions and is never a generic backup
- Producer-relative charge labels and hydrolysis percentages are kept on separate scales
- Incumbent and candidate viscosity values are compared only with their concentration, temperature and method preserved
- Selection is made on equal-active, same-duty testing rather than model-name similarity
- Current documents and commercial terms are rechecked before quotation
Applications
- Exact FLOPAM EM 532 procurement enquiries where the buyer can provide the current label and operating duty
- Oilfield-PHPA emulsion screening where the treated fluid, salinity, temperature and acceptance target fit the documented ZJ033 scope
- Salt-resistant or high-salinity PHPA screening where the documented ZJ050 scope is relevant
- Correcting a proposed changeover that compared viscosity or charge labels across manufacturers without a common test basis
Get a Quote for FLOPAM EM 532 Alternative Supply
Start with the exact EM 532 label, the current datasheet if available, quantity, destination, treated stream, salinity, temperature, present as-supplied dose, make-down and pump details, and the result your process must hold.
Related Articles
Start with the duty: this page does not convert a model name into a grade promise
The useful commercial answer is direct: ChinaPAM can take an exact FLOPAM EM 532 enquiry, review the operating duty and return a controlled test and selection plan with a current quotation. The route is not chosen from the EM 532 name alone.
A buyer asking about a compatible oilfield-PHPA duty can begin with ZJ033. ZJ050 enters only when the process actually requires salt resistance, high salinity or its higher documented hydrolysis range. If the application does not match those document scopes, neither grade is preselected and the enquiry stays open for further screening.
Four facts established by the exact historical EM 532 column
All incumbent facts below come from the exact FLOPAM EM 532 column on physical page 6 of the SNF 2007 emulsions catalogue. They are historical, attributed and marked indicative by that catalogue.
| Established fact | Exact source | What it does not prove |
|---|---|---|
| Anionic polyacrylamide emulsion with Medium charge and High molecular weight. | SNF emulsions catalogue 2007, physical page 6, EM 532 identity/charge/MW rows. | No numeric conversion to a ChinaPAM hydrolysis percentage and no one-to-one grade match. |
| Approx. bulk viscosity 1,200 cps, bulk density 1.04 and average non-volatile solids 36.0%. | Same exact column, bulk-property rows. | No current contractual specification and no direct analytical equivalence to a ChinaPAM solids value. |
| Dilution 58 to a 5 g/L active condition, approx. 1,800 cps at 5 g/L, maximum operating concentration 5 g/L and DI-water solution stability 8 days. | Same exact column, working-solution rows. | No direct comparison with candidate viscosity values measured at another concentration, temperature or method. |
| Six-month shelf life, 0–35°C storage and 25 kg pail, 1,050 kg IBC or 22–24 t bulk packing. | Same exact column, storage/packing rows and catalogue disclaimer. | No proof of current stock, present packaging, lead time or availability. |
Failure controls that protect the changeover decision
These controls address the specific errors that the available product documents make possible.
| Risk | Why it matters | Verification step |
|---|---|---|
| Cross-manufacturer charge mapping | SNF Medium charge and ChinaPAM hydrolysis percentages are separate producer scales. | Keep the scales separate and rank routes only from same-duty comparative testing. |
| Application-duty mismatch | The ZJ033 and ZJ050 documents cover industrial/oilfield PHPA duty, while the historical EM 532 row does not establish the buyer's application. | Confirm fluid chemistry, salinity, temperature, equipment and acceptance metrics before either route is screened. |
| Non-comparable viscosity or dose basis | The incumbent figure is reported at 5 g/L active, while the ChinaPAM document values use different preparation conditions. | Normalise dose to active polymer and preserve concentration, temperature, water and method for every reading. |
| Salt-resistance overreach | ZJ050's salt-resistant identity does not make it a general-purpose backup. | Use ZJ050 only when the buyer confirms high salinity or the relevant higher hydrolysis requirement. |
| Sibling or currentness error | EM 533/EM 630 values and a 2007 indicative row can be mistaken for EM 532 current facts. | Lock the exact EM 532 label and recheck current documents and commercial terms before quotation. |
Ten questions procurement should close before ordering
A usable request answers these questions in order; unanswered items stay open rather than becoming assumptions.
| Procurement question | ChinaPAM answer |
|---|---|
| Can ChinaPAM respond to this exact enquiry? | Yes. ChinaPAM provides an exact-model selection service and quotation after duty review; no exact substitute is promised. |
| Which incumbent must be confirmed? | FLOPAM EM 532, verified from the current label or datasheet; no EM 533 or EM 630 fact transfer. |
| Which route is screened first? | ZJ033 only for a confirmed compatible oilfield-PHPA duty. |
| When is the backup relevant? | ZJ050 only for salt resistance, high salinity or the relevant higher hydrolysis range. |
| What must be disclosed before the quote? | Same form and ionic family do not prove equal chemistry, charge position or performance. |
| What buyer inputs are required? | Current label/datasheet, duty, pH, solids or turbidity, salinity, temperature, present dose, make-down, pump, quantity and destination. |
| How is the trial kept fair? | Prepare each product by its own instructions and compare equal-active doses on the same feed with fixed mixing and measurement windows. |
| Which failure controls are mandatory? | Separate producer scales, verify duty, preserve test conditions, restrict ZJ050 to high-salinity scope and keep sibling facts out. |
| What do the available documents confirm? | They confirm the attributed historical incumbent facts and support a conditional selection route. Current availability and commercial terms are confirmed in the quotation; performance is determined by the agreed same-duty test. |
| What is the next commercial step? | Submit the exact label and duty data; ChinaPAM rechecks the applicable documents and availability, then returns the test plan and quotation. |
Trial and acceptance plan
Prepare the incumbent and each candidate by its own applicable instructions. Compare equal-active starting doses on the same representative feed, bracket dosage, keep mixing and measurement windows constant, and record the duty endpoint, clarity, floc strength, solution age and operability.
Agree the acceptance metrics before the first run. Depending on the confirmed PHPA duty, these may include viscosity response, fluid-loss or shale-control endpoint, solution handling, pumpability, active dose and stability under the buyer's salinity and temperature. Advance only when the selected route meets those declared metrics on representative material.
Current ChinaPAM grade documents, availability, price, lead time and sample arrangements are confirmed for the selected route in the quotation. The historical FLOPAM catalogue does not establish current commercial terms for either side.
Brand Equivalents & Replacements
ChinaPAM accepts a confirmed FLOPAM EM 532 enquiry and builds a same-form anionic emulsion screen only after the duty is understood. ZJ033 is the first screen for a compatible oilfield-PHPA duty; ZJ050 is considered only for salt-resistant or high-salinity conditions. Same form and ionic family do not prove equal chemistry or performance, and neither route is presented as a drop-in substitute.
| Brand | Grade | Notes |
|---|---|---|
| SNF / FLOPAM | FLOPAM EM 532 | Historical 2007 catalogue identity: anionic emulsion, Medium charge and High molecular weight. ChinaPAM screens ZJ033 only for compatible oilfield-PHPA duty and reserves ZJ050 for salt-resistant or high-salinity conditions. Selection service only; no exact-equivalence claim. |
Need a replacement for a different grade? Contact us with your current product specs.
Dosage Guide
Prepare the incumbent and each candidate by its own applicable instructions. Compare equal-active starting doses on the same representative feed, bracket dosage, keep mixing and measurement windows constant, and record the duty endpoint, clarity, floc strength, solution age and operability.
Frequently Asked Questions — FLOPAM EM 532 Alternative — Anionic Emulsion Selection for PHPA Duty
Can ChinaPAM supply an alternative route for FLOPAM EM 532?
Yes. ChinaPAM accepts exact EM 532 enquiries and can quote an exact-model anionic emulsion selection route after the duty is reviewed. ZJ033 is screened first only for compatible oilfield-PHPA duty; ZJ050 is reserved for salt-resistant or high-salinity conditions. No identical-formula or guaranteed-performance claim is made.
Why is ZJ033 not automatically called the equivalent grade?
Because the available published documents do not calibrate SNF's Medium-charge label against ChinaPAM hydrolysis percentages, and the historical EM 532 row does not establish the buyer's application duty. ZJ033 is a same-form first-screen route only after a compatible PHPA duty is confirmed.
When should ZJ050 be considered?
Only when the buyer confirms salt resistance, high salinity or a need aligned with ZJ050's documented higher hydrolysis range. Its salt-resistant identity is a condition for use, not proof that it is a universal EM 532 backup.
Can I compare the published viscosity numbers directly?
No. The historical EM 532 figure is about 1,800 cps at 5 g/L active, while the ZJ documents use another preparation concentration, temperature and method. Keep every reading tied to its own method and decide from equal-active, same-duty testing.
What information starts the FLOPAM EM 532 selection?
Send the exact label, the current datasheet if available, treated fluid, salinity, temperature, present as-supplied dose, make-down and pump details, acceptance metric, quantity and destination.
What is confirmed in the quotation?
Current ChinaPAM grade documents, availability, price, lead time and sample arrangements are confirmed for the selected route in the quotation. The historical FLOPAM catalogue does not establish current commercial terms for either side.
Related Products
Trademark notice. FLOPAM EM 532 and all other third-party product and brand names on this page are trademarks or registered trademarks of their respective owners. Henan Jinghua New Material Technology Co., Ltd. is not affiliated with, endorsed by, sponsored by or authorised by those owners, and no such relationship is implied. Those names are used here for the sole purpose of identifying the products our grades are compared against, which is necessary to describe what we supply. Our products are separately branded ChinaPAM grades and are not licensed copies. Third-party facts on this page are attributed to SNF sas's 2007 emulsions catalogue, physical page 6, exact FLOPAM EM 532 column; the document is historical, its figures are marked indicative, and no EM 533 or EM 630 facts are transferred here. Performance on your process should be confirmed by jar test or CST test before any change of supply.