FLOPAM AH 912 SH Equivalent: Very-Low-Charge PAM Supply Route
ChinaPAM supplies low-charge anionic PAM powder with 1082 as the primary route for FLOPAM AH 912 SH duty. Use 1042 as a second route when lower-molecular-weight preparation or delivery constraints matter. Ask for current pricing or sample options using the grade name, a bag-label photo or your purchasing requirement; process details can follow.
Supply Route Comparison
Published reference data and the ChinaPAM route for SNF FLOPAM AH 912 SH
Competitor reference: SNF SAS Catalogue 2007 Poudres, pages 32 and 54. Historical indicative values, not current contractual specifications. Each supplier sets its own qualitative bands. FLOPAM is a trademark of SNF; ChinaPAM supplies its own products and is not affiliated with or endorsed by SNF.
| Parameter | ChinaPAM Supply Route | SNF FLOPAM AH 912 SH |
|---|---|---|
| Polymer type | Anionic PAM powder | Very-low-charge powder; low-anionic location in p54 chart |
| Charge band | Low (our scale) | Very Low (SNF 2007 p32) |
| Molecular-weight band | Very High (our scale) | Very High (SNF 2007 p32) |
| Brookfield at 5 / 2.5 / 1 g/L | Confirm applicable grade data | Approximately 450 / 180 / 100 cps (SNF 2007 p32) |
| Recommended make-up | 1-3 g/L | 5 g/L (SNF 2007 p32) |
| Maximum make-up | 5 g/L | 10 g/L (SNF 2007 p32) |
| Dissolution | Within 60 min at working concentration | 150 min in DI water at 5 g/L and 25 C (SNF 2007 p32) |
Specifications
| Primary supply grade | 1082 |
| Our polymer | Anionic PAM powder |
| Our charge band | Low (ChinaPAM scale) |
| Our molecular-weight band | Very High (ChinaPAM scale) |
| Our recommended make-up | 1-3 g/L |
| Our maximum make-up | 5 g/L |
| Our dissolution | Within 60 min at working concentration |
| Conditional alternate | 1042: Low charge, Low molecular-weight band; only for a justified lower-band trial |
Key Features
- 1082 same-type trial route with descriptor differences disclosed
- Exact AH 912 SH identity and historical source retained
- Preparation and delivered dose checked on actual feed
Applications
- Alternative supply screening for buyer-specified FLOPAM AH 912 SH duty
- Make-up and dosing-system checks during an incumbent polymer changeover
- Feed-specific clarification, settling and downstream dewatering trials
Get a Quote for SNF FLOPAM AH 912 SH Alternative Supply
Start with the grade name, a bag-label photo or your purchasing requirement. We can discuss current pricing and sample options now; process details can follow.
Related Articles
Read the exact SH entry
SNF SAS Catalogue 2007 Poudres, page 32, lists AH 912 SH powder at Very Low charge and Very High molecular weight, with approximate Brookfield readings of 450 / 180 / 100 cps at 5 / 2.5 / 1 g/L. Recommended make-up is 5 g/L, maximum 10 g/L, and dissolution is 150 minutes in deionized water at 5 g/L and 25 degrees C. These historical averages are not current contractual specifications.
The catalogue's page 54 anionicity chart places AH 912 near the low-anionic end. Its location in the contents beside nonionic grades must not be used to turn the Very Low charge entry into a strict nonionic claim. The bare AH 912 entry also differs: High molecular weight, 400 / 160 / 60 cps, and 90-minute dissolution under the stated conditions.
Primary and conditional alternative
1082 is our Very High molecular-weight, Low-charge anionic powder starting point. Grade 1042 is also Low-charge anionic powder, but in our Low molecular-weight band. Include 1042 only when a lower-band comparison addresses a real preparation, viscosity or delivery question; its label does not guarantee a specific solution viscosity or a better result. Nonionic 1003 is a different ion-type route and is not the default alternative on this page.
Our powder preparation is 1-3 g/L recommended, maximum 5 g/L, with dissolution within 60 minutes at working concentration. Keep these instructions separate from SNF's historical make-up conditions and establish the treatment dose on the actual feed.
Two selection failures to avoid
Classification: treating AH 912 SH as strictly nonionic can send the inquiry to the wrong polymer family. Confirm the exact bag label and required charge behavior, then compare the low-charge anionic starting route on the actual feed. Do not treat an old product-family heading as a measured charge result.
Suffix and solution quality: using the bare AH 912 90-minute release schedule for SH overlooks its 150-minute reference. Verify maturation and measured pump delivery at the selected concentration before interpreting poor clarification or dewatering as a need to change grade or increase dose. Evaluate 1082 and any justified 1042 trial at controlled polymer mass delivery.
Discuss the two trial routes
Send the full incumbent grade, make-up settings, preparation constraints, treatment objective and monthly requirement. We will discuss 1082 and, where justified, a 1042 comparison, sample arrangements and applicable order documents.
Dosage Guide
Prepare our powder at 1-3 g/L, maximum 5 g/L, with dissolution within 60 minutes at the working concentration. Make-up concentration is different from the treatment dose. Establish the dose on your actual feed and verify measured polymer delivery.
Frequently Asked Questions — FLOPAM AH 912 SH Equivalent: Very-Low-Charge PAM Supply Route
What supply route can I discuss for FLOPAM AH 912 SH duty?
ChinaPAM supplies low-charge anionic PAM powder with 1082 as the primary route for FLOPAM AH 912 SH duty. Use 1042 as a second route when lower-molecular-weight preparation or delivery constraints matter. Ask for current pricing or sample options using the grade name, a bag-label photo or your purchasing requirement; process details can follow.
What must I check before changing supply?
Classification: treating AH 912 SH as strictly nonionic can send the inquiry to the wrong polymer family. Confirm the exact bag label and required charge behavior, then compare the low-charge anionic starting route on the actual feed. Do not treat an old product-family heading as a measured charge result.
What information should I send for a quotation?
Start with the grade name, a bag-label photo or your purchasing requirement. We can discuss current pricing and sample options now; process details can follow.
Related Products
APAM High Molecular Weight
Anionic PAM with 18-28 million MW for municipal and industrial wastewater clarification.
View DetailsApplication Solutions
View Product Details →
Trademark notice. SNF FLOPAM AH 912 SH and all other third-party product and brand names on this page are trademarks or registered trademarks of their respective owners. Henan Jinghua New Material Technology Co., Ltd. is not affiliated with, endorsed by, sponsored by or authorised by those owners, and no such relationship is implied. Those names are used here for the sole purpose of identifying the products our grades are compared against, which is necessary to describe what we supply. Our products are independently manufactured and are not licensed copies. Grade descriptors quoted for third-party products are taken from each manufacturer’s own published literature and follow that manufacturer’s own scale; we do not publish figures those manufacturers do not publish. Performance on your process should be confirmed by jar test or CST test before any change of supply.