FLOPAM FO 4000 SSH Equivalent Screening
ChinaPAM supplies cationic polyacrylamide powder routes for all seven listed FLOPAM FO 4000 SSH enquiries and can quote a model-specific screening program. Send the exact SSH model or bag-label photo, current dosage, make-down concentration and conditions, and the separation result you need. We will select the primary route, define the comparison test and state every charge or molecular-weight difference before the route is quoted.
Supply Route Comparison
Published reference data and the ChinaPAM route for SNF FLOPAM FO 4000 SSH series
Source identity: SNF SAS, Catalogue 2007 Poudres, a historical catalogue issued in 2007. SNF states that its data are for information and do not constitute a specification. Every SNF value on this page is therefore historical indicative material under the stated SNF test conditions; it is not a ChinaPAM specification and does not describe today's SNF offer. SNF and ChinaPAM use separate qualitative charge and molecular-weight scales, so the labels do not convert numerically across the two ranges.
| Parameter | ChinaPAM Supply Route | SNF FLOPAM FO 4000 SSH series |
|---|---|---|
| Identity | A separately branded ChinaPAM cationic powder screening route selected for the exact SSH enquiry | Seven exact FO 4000 SSH grades listed in SNF Catalogue 2007 |
| Charge basis | ChinaPAM owned-grade bands used only inside the ChinaPAM range | Historical SNF bands: Very Low, Low, Medium or High by exact SSH model |
| Molecular-weight basis | Medium- or High-MW screening lanes by route; differences are shown in the model matrix | Very-high MW for all seven grades in the historical catalogue |
| Route status | FO 4140 SSH selection service; the other six named same-type screening routes | Historical model identity only; the catalogue is not a ChinaPAM route decision |
| Selection close | Actual-feed test under the buyer's make-down and dosing conditions | Historical indicative catalogue values under SNF test conditions |
| Commercial terms | Confirmed in the quotation for the selected ChinaPAM route | Not established by the historical source used on this page |
Specifications
| ChinaPAM Product Form | Cationic polyacrylamide powder |
| Exact SSH Models Covered | FO 4140, 4190, 4240, 4290, 4350, 4440 and 4650 SSH |
| FO 4140 SSH Route | Selection service: C8008 first; C8001 or C8015 second |
| FO 4190 / 4240 SSH Route | C8008 first; C8001 or C8015 second |
| FO 4290 / 4350 SSH Route | C8001 or C8015 first; C8003, C8004, C8005, C8035 or C8045 second |
| FO 4440 / 4650 SSH Route | C8003, C8004, C8005, C8035 or C8045 first; C8002 or C8025 second |
| Selection Basis | Exact suffix, qualitative charge/MW position, make-down conditions and actual-feed test |
| Commercial Boundary | Packaging, order quantity and available documents are confirmed for the selected ChinaPAM route in the quotation |
Key Features
- One searchable Hub covering seven exact FO 4000 SSH purchasing lines
- A named primary and secondary ChinaPAM route for every listed SSH model
- Historical SNF facts kept separate from ChinaPAM route facts
- Charge and molecular-weight gaps stated before the buyer selects a test route
- Actual-feed comparison plan tied to the buyer's current dosage and make-down conditions
- Owned Jinghua/ChinaPAM warehouse image used for supply-side identity
Applications
- Supplier-change screening for an exact FO 4000 SSH purchasing line
- Suffix and bag-label verification before route selection
- Actual-feed jar-test comparison of shortlisted cationic powder routes
- Make-down and dosing review before a supply change
Get a Quote for SNF FLOPAM FO 4000 SSH series Alternative Supply
Send the exact SSH model or bag-label photo. Add current dosage, make-down conditions, separation target, quantity and destination when available; ChinaPAM will name the screening route and prepare the route-specific quotation.
Related Articles
Seven Exact SSH Models and Their ChinaPAM Screening Routes
Choose the row that matches the full bag label or purchasing line. The route names are firm screening starts from the owned ChinaPAM dictionary. They do not turn one manufacturer's qualitative scale into the other manufacturer's scale.
C8006 and C8055 are not primary or secondary routes. For FO 4440 SSH or FO 4650 SSH only, they may be considered as a tertiary MW-proximity laboratory branch after the buyer accepts a one-band charge difference: Very High on the ChinaPAM scale versus the historical High target.
| Exact SSH model | Historical SNF target | Primary ChinaPAM route | Secondary route | Commercial status |
|---|---|---|---|---|
| FO 4140 SSH | Very Low charge / Very-high MW | C8008 | C8001 or C8015 | Selection service; no documented Very-Low + Very-High-MW owned row |
| FO 4190 SSH | Low charge / Very-high MW | C8008 | C8001 or C8015 | Same-type screening; primary route MW is Medium |
| FO 4240 SSH | Low charge / Very-high MW | C8008 | C8001 or C8015 | Same-type screening; primary route MW is Medium |
| FO 4290 SSH | Medium charge / Very-high MW | C8001 or C8015 | C8003, C8004, C8005, C8035 or C8045 | Same-type screening; primary MW Medium, secondary MW High |
| FO 4350 SSH | Medium charge / Very-high MW | C8001 or C8015 | C8003, C8004, C8005, C8035 or C8045 | Same-type screening; primary MW Medium, secondary MW High |
| FO 4440 SSH | High charge / Very-high MW | C8003, C8004, C8005, C8035 or C8045 | C8002 or C8025 | Same-type screening; primary MW High, secondary MW Medium |
| FO 4650 SSH | High charge / Very-high MW | C8003, C8004, C8005, C8035 or C8045 | C8002 or C8025 | Same-type screening; primary MW High, secondary MW Medium |
Three Historical Facts Buyers Can Trace to the 2007 Catalogue
Fact 1 — model identity and charge: the historical source lists FO 4140 SSH at Very Low charge, FO 4190 SSH and FO 4240 SSH at Low, FO 4290 SSH and FO 4350 SSH at Medium, and FO 4440 SSH and FO 4650 SSH at High. It labels all seven Very-high MW. FO 4440 SSH must stay on the High-charge row; its SSH suffix changes the target from the bare-grade position.
Fact 2 — dissolution under the historical test: FO 4140 SSH, FO 4190 SSH and FO 4240 SSH list 120 minutes; FO 4290 SSH, FO 4350 SSH, FO 4440 SSH and FO 4650 SSH list 90 minutes. The catalogue condition is 5 g/L in deionised water at 25°C. These times size the historical comparison condition and are not ChinaPAM dissolution specifications.
Fact 3 — storage and packing in the historical source: the table lists 0–35°C storage, while the 24-month shelf-life footnote requires stable indoor storage at 5–30°C. It lists bulk density 0.80 and 25 kg bags or 750 kg big bags for these grades. Those figures describe the historical SNF table and do not set ChinaPAM commercial terms.
| Exact SSH model | SNF charge / MW | Historical viscosity, cps | Historical dissolution |
|---|---|---|---|
| FO 4140 SSH | Very Low / Very-high | 310 / 140 / 50 | 120 min |
| FO 4190 SSH | Low / Very-high | 560 / 260 / 120 | 120 min |
| FO 4240 SSH | Low / Very-high | 600 / 340 / 140 | 120 min |
| FO 4290 SSH | Medium / Very-high | 700 / 350 / 120 | 90 min |
| FO 4350 SSH | Medium / Very-high | 650 / 360 / 150 | 90 min |
| FO 4440 SSH | High / Very-high | 710 / 380 / 180 | 90 min |
| FO 4650 SSH | High / Very-high | 760 / 390 / 170 | 90 min |
Matched, Close, Unknown and Test: Read the Route Correctly
This matrix separates what the evidence supports from what the buyer and ChinaPAM still need to close. A matched charge band is useful for ordering the screening sequence; it does not prove cross-brand chemistry or process performance.
| Status | What it means on this page | Buyer action |
|---|---|---|
| Matched | The historical target and a ChinaPAM route use the same qualitative charge word for FO 4190, 4240, 4290, 4350, 4440 or 4650 SSH | Keep the exact suffix and test the named primary route first |
| Close | FO 4140 SSH starts one charge band away; all named primary routes carry an MW difference from the historical Very-high label | Keep both differences visible in the sample plan |
| Unknown | Cross-brand numerical charge, polymer structure, actual-feed result and current commercial terms are not established by the accepted sources | Supply the operating target and required commercial details |
| Test | The actual feed, make-down conditions, current dosage and required separation result close the selection | Run the shortlisted routes against one baseline under controlled conditions |
Two Evidence-Based Failure Modes to Prevent
Both failures come from treating a screening clue as a finished purchasing decision. The control is to preserve the full suffix, state the band gap and close the route on the buyer's feed.
| Failure mode | Evidence basis | Likely consequence | Control |
|---|---|---|---|
| Cross-brand qualitative labels treated as numerical alignment | Neither accepted scale supplies a cross-brand wt% or mole% conversion | A route is chosen at the wrong charge position | Treat the bands as screening order only; measure or test the actual sample when numerical position matters |
| Low or Very-Low charge plus Very-high MW carried straight onto the owned range | The full 26-grade traversal found no documented ChinaPAM cationic powder row with that combination | The buyer overlooks the charge/MW tradeoff for FO 4140, 4190 or 4240 SSH | Use the named C8008-led route, disclose the MW gap and compare it on the actual feed |
Actual-Feed Screening Plan
Keep the incumbent material as the baseline. Prepare the baseline and shortlisted ChinaPAM route under controlled water quality, concentration, mixing energy, maturation time and solution age. Record whether each solution reaches a stable condition before dosing.
Dose the same representative feed in steps with the same mixing sequence. Record the buyer's separation target, current dosage, visible solids/liquid response and the point where additional polymer no longer improves the required result. Select the route only after the buyer-defined pass condition is met consistently.
| Input to send | Why ChinaPAM needs it |
|---|---|
| Full model with SSH suffix or bag-label photo | Locks the correct model row and prevents bare, SH, SEP or VHM suffix overlap |
| Current dosage and solution concentration | Sets the baseline and comparison window |
| Water, temperature, mixing and maturation conditions | Makes the preparation comparison reproducible |
| Feed description and separation target | Defines the pass condition |
| Expected quantity and destination | Lets ChinaPAM prepare a route-specific quotation without assuming commercial terms |
Ten Procurement Decisions Closed on One Page
A buyer can start with the exact model and fill the remaining fields as they become available. Missing process detail does not stop the first route answer; it determines how narrow the final shortlist can be.
| No. | Decision module | Page decision or required input |
|---|---|---|
| 1 | Identity and suffix | Use the full FO model plus SSH; a bag-label photo is accepted as the starting record |
| 2 | Physical form | Historical line and ChinaPAM supply route are powder; keep any other form on a separate enquiry |
| 3 | Ionicity | Cationic route only for this Hub |
| 4 | Qualitative MW and charge | Use the seven-row model matrix; do not convert the two manufacturers' scales numerically |
| 5 | Particle size and bulk density | Historical bulk density is 0.80; no ChinaPAM particle-size or bulk-density value is claimed until a route is selected |
| 6 | Dissolution and dosing conditions | Buyer supplies concentration, water, temperature, mixing, maturation, solution age and current dose |
| 7 | Storage and shelf-life boundary | Historical conditions remain attributed to SNF 2007; ChinaPAM conditions come only from the selected route's own information |
| 8 | Packaging and order quantity | Buyer supplies expected quantity and destination; ChinaPAM confirms the offered packaging and commercial terms in the route-specific quotation |
| 9 | Selection and sample path | Primary route first, secondary route second, then actual-feed jar-test ranking against the incumbent baseline |
| 10 | Documents and regulatory boundary | Buyer states required documents and end-use requirements; ChinaPAM confirms what applies to the selected route before the purchasing decision |
ChinaPAM Supply Identity and Evidence Boundary
The hero asset is the existing owned Jinghua/ChinaPAM warehouse photograph at /images/factory/warehouse-bags.jpg. It shows bagged polymer stored on warehouse racks and carries no unrelated company identity. Its role is to show the real supply environment, not to assert a model specification.
The screening record stays attached to the exact ChinaPAM route chosen from the owned grade dictionary. Any product or QC document discussed with the buyer must belong to that selected ChinaPAM route and the actual commercial transaction. Historical SNF catalogue pages are source evidence for model identity and comparison conditions only; they are not ChinaPAM QC records.
Start with the Exact SSH Model
Send FO 4140 SSH, FO 4190 SSH, FO 4240 SSH, FO 4290 SSH, FO 4350 SSH, FO 4440 SSH or FO 4650 SSH through the page form, WhatsApp or email. Add the bag label, current dosage, make-down conditions, separation target, quantity and destination when available. ChinaPAM will answer with the named screening route, the remaining evidence gap and the next comparison step.
Frequently Asked Questions — FLOPAM FO 4000 SSH Equivalent Screening
Can ChinaPAM supply for an FO 4000 SSH enquiry?
Yes. ChinaPAM supplies cationic polyacrylamide powder routes for the seven SSH models on this page and can quote a model-specific screening program. Send the exact SSH model or bag label, current dosage, make-down conditions and separation target.
Which ChinaPAM route starts the FO 4140 SSH screening?
C8008 is the primary screening route, with C8001 or C8015 as the secondary route. This is a selection service because the owned ChinaPAM dictionary has no Very-Low-charge plus Very-High-MW cationic powder row. The charge and MW differences stay visible in the test plan.
Which routes cover FO 4190 SSH and FO 4240 SSH?
C8008 is the primary route and C8001 or C8015 is the secondary route. C8008 matches the historical Low charge band at a qualitative level inside the separate ChinaPAM scale, while its Medium MW remains below the historical SNF Very-high MW label. The actual-feed test decides the route.
Which routes cover FO 4290 SSH and FO 4350 SSH?
C8001 or C8015 is the primary route. C8003, C8004, C8005, C8035 or C8045 is the secondary route. The first group matches the Medium charge target inside the ChinaPAM range; the second group moves to High charge and High MW. Both remain screening choices rather than a numerical cross-brand conversion.
Which routes cover FO 4440 SSH and FO 4650 SSH?
C8003, C8004, C8005, C8035 or C8045 is the primary route; C8002 or C8025 is secondary. C8006 or C8055 may enter once as a tertiary MW-proximity laboratory branch only when the buyer accepts that their Very High charge sits one band above the historical High-charge target.
What should I send to start the selection?
Send the full model with SSH suffix or a bag-label photo, current dosage, make-down concentration, water and mixing conditions, solution age at dosing, separation target, expected quantity and destination. ChinaPAM can then name the route and define the comparison plan.
How are packaging and documents handled?
The historical SNF pack sizes are source facts only. ChinaPAM confirms packaging, order quantity and the available document set for the selected ChinaPAM route in the quotation. No current ChinaPAM commercial term is inferred from the 2007 catalogue.
Related Products
Trademark notice. SNF FLOPAM FO 4000 SSH series and all other third-party product and brand names on this page are trademarks or registered trademarks of their respective owners. Henan Jinghua New Material Technology Co., Ltd. is not affiliated with, endorsed by, sponsored by or authorised by those owners, and no such relationship is implied. Those names are used here for the sole purpose of identifying the products our grades are compared against, which is necessary to describe what we supply. ChinaPAM products are separately branded grades and are not licensed copies. Grade descriptors quoted for third-party products are taken from each manufacturer’s own published literature and follow that manufacturer’s own scale; we do not publish figures those manufacturers do not publish. Performance on your process should be confirmed by jar test or CST test before any change of supply.